Increased Productivity Example #4



Digitized Signal from Magnetic Recording

Magnetic recording of transitions written onto a computer disc drive may produce an isolated pulse as shown below. This pulse comes from a disc drive's read/write channel. Each transition will cause such a signal to occur.

1980s Isolated Readback Pulse

Figure 2.5.1 An isolated Readback Pulse from a disc drive

The signal's shape is very important to the electrical engineering development groups of disc drives. A readback pulse should be symmetric and have a relatively fast rise time (i.e. steep slope) for improved peak detection capability. A math model for the pulse can help gain insight into what electronic sub-system/components are causing the pulse to be asymmetric or have a slow rise time.

The longitudinal magnetic force was assumed the main contributing factor in determining a readback pulse shape, before the early 1980's. This force component was modeled by a series of three Lorentz functions. These functions have varying independent parameters that are dependent upon the drive's Thin-Film-Head (TFH) composition, size and shape. The value for these parameters was helpful in understanding a design and manufacturing flaw.

A Lorentz function has represented/modeled an isolated readback pulse for some time. The basic Lorentz function is defined as y = Basic Lorentz function. The isolated pulse model is a composite of three Lorentz functions as stated here:

Great Isolated Pulse Model

where
vi = Amplitude of a Lorentz pulse;
pw_50i = Lorentz pulse width, measured at 50% height of vi; and,
ti = Origin of the ith Lorentz.

In the early 1980s, this model was found to be inadequate when Thin Film Heads were starting to be used in disc drives. An examination of the math model versus actual data plots showed that the 1970s model was no longer sufficient. The longitudinal force coupled with the increased vertical force were used to provide an excellent model for TFH readback pulses in the mid 1980s as shown in the following math model, signal2:

Modified Lorentz function 4 Isolated Pulse

where
vi = Amplitude of a longitudinal magnetic force;
vci = Amplitude of vertical force component;
pw_50i = Lorentz pulse width, measured at 50% height of vi; and,
ti = Origin of the ith Lorentz function.


Parameter Estimation Problem

Find the three Lorentz parameter set (vi, vci, pw_50i and ti) values necessary to fit the Signal2(t) model to a digitized isolated readback pulse. Assume a total of 512 equal spaced points (i.e. Δt constant between points).

Note: Our CurvFit application will solve this curve fit problem with a Lorentz series or a 'Modified' Lorentz series.

Increased Productivity Example #4 Source Code:



Problem Curvefit
common v(3), vc(3), pw_50(3), time0(3),
npoints, data(512), signal(512), error(512)
data v/ -.1, 1., .05/, vc/ .1, .1, .1/,
pw_50/ 50, 40, 50/
delta_t = .9765625 : npoints = 512
open( 11, file="pulse.dat", status=old)
do j = 1, npoints
read(11,*) data(j)
signal(j) = (j - npoints/2) * delta_t
end do
FIND v, vc, pw_50, time0; IN Pulse;
TO MATCH error

! 1. plot signal & data vs. time here
! 2. plot error vs. time here
end
Model Pulse
common v(3), vc(3), pw_50(3), time0(3),
npoints, data(512), signal(512), error(512)
do j = 1, npoints
sum = 0
do i = 1, 3
sum = sum + Lorentz( time(j), v(i), vc(i),
pw_50(i), time0(i))
end do
signal(j) = sum : error(j) = data(j) - signal(j)
end do
return
end
Function Lorentz( t, v_i, vc_i, pw_50_i, t_i)
x = (t - t_i) / pw_50_i : num = v_i + vc_i * x
den = 1 + x**2 : Lorentz = num / den
return
end

Increased Productivity Example #4 Other Information:



Relating Model and Design Parameters

Assuming the digitized data fits a math model with quadratic convergence, how do the model parameters (M) relate to the design dimensions? For example, this present TFH example has model parameters vi, pw_50i, and ti (for i = 1 to 3) while the design parameters as shown in the following diagram are A, B, C, D, E, & F.

Magnet Geometry of Thin-Film-Head
Figure 2.5.2 A TFH at flying height F above a disc drive's media

The governing equations may not be known for sure but someone with an understanding of the magnetic effects on a TFH could at least determine whether the parameters are proportional or inversely proportional. This would help as one starts building an understanding of what a math model might be in order to find the optimum design parameters to produce a symmetric and "narrow" (readback) pulse with no (or minimal) undershoots as represented in the curve shown below

Optimum pulse shape?

Ideal Symetric Isolated Pulse
Figure 2.5.3 An "ideal" Readback Pulse from a disc drive

Through acquisition of many digitized pulses with varying pulse model parameters will eventually provide the necessary design parameters for an optimum pulse. This would require many man-hours of time. Another option would be to do Pulse Slimming via a Matched Filter as Memorex Corp. did in the 1980s.

This Magnetic Recording problem is another increased productivity example do to using Calculus (level) programming.

HTML code for linking to this page:


<a href=""><img style="float:left; width:100px" src="http://fortranCalculus.info/image/readrit-pic2.png"/> <strong>Model 4 Digitized Signal from Magnetic Recording</strong> </a>, Isolated Readback Pulse, Modeling & Simulation.

< < Back

Next > >

 
Valid CSS! Calculus (level) Problem-Solving for Engineers & Scientists Author's Amazon Account

Textbooks - Parameter Estimation 4 ODE/PDE - Signal Analysis / Spectral Estimation - Body Plasma - Solar Cell
Increasing Productivity Examples: AC Motor Design - Matched Filters - Pulse Slimming / InterSymbol Interference - Pilot (safe) Ejection - PharmacoKinetics Simulation - Poisson's (Differential) Equation - Schrodinger (Differential) Equation - BVP 4 PDE Equations - Implicit (Differential) Equations